Bedliner Batch Mix

PRODUCT INFORMATION

100% solids, two component polyurea hybrid ceramic putty
Contains no VOC’s
Good resistance to inorganic bases, acids and hydrocarbon solvents
Fair resistance to oxygenated and chlorinated solvent
Good resistance to hot water up to 180° F

Primary Applications

Hand mix/batch material
Use as a non immersion grade tank lining for steel and concrete tanks
Lining of material handling equipment
Coating of urethane or expanded polystyrene foam insulation
Waterproofing of structures
Protection of concrete from acid and alkaline materials
Use as an environmental containment barrier with or without geotextiles
Used for lining interior of truck beds
Use as tank lining material

Color

Standard is black. Contact Enhanced Flooring Products LLC for additional colors.

Accelerant Additive

The accelerant additive may be added to the ORMPH or the Mining Putty at the rate of 2-5 drops per pint of mixed product. The number of drops is measured by the number of drops off of a 3/8” to 7/16” wide flat blade screwdriver that has been dipped into the bottle of accelerant. This will speed up the product cure from mix up to tack free and Sandable to about 30 minutes. To adjust this time, add or subtract drops of the accelerant.

Storage

12 months in unopened containers at 50-90° F

Toxicity

Iso component contains polymeric isocyanate requiring fresh air supplyrespirator, gloves and protective clothing during application

Typical Physical Properties

Tensile Strength:ASTM D4122800
Elongation (%) ASTM D412225%
Tear Strength (PLI)ASTM D-624350
Hardness (shore A)ASTM D-224090
Abrasion resistance Excellent
Viscosity B sideCPS500-600
Viscosity A sideCPS500-600
Ratio A/BBV2:1
Density B side1.025 
Density A side1.14 
Flash pointASTM D-56>720° F
VOC TestingCAN/ULC-S774P >200° F
Weight8.5 lbs/gallon 
Gel Time25 to 30 seconds 
Tack Free Time10 minutes 
Foot traffic1 hour 
DFT coverage250 mils6/2/ga

Primer

ORPR511 is the recommended primer for concrete, wood and metal substrates

Application:

Surface Preparation: General: Surface must be properly prepared prior to application. This could entail shot blasting or grin ding, scrubbing, high pressure detergent washing, steam cleaning or solvent wiping of the surface to remove dirt, oil, grease pollutants and other contaminan ts. Allow the surface to thoroughly dry. Once dry, remove loose or excess mortar or other material that may work to impair adhesi on.

Materials needed to mix: 2 ½ gal or 5 gallon pail, electric drill and spiral mixer.

Mixing/Stirring:

Pour part “A” into a clean pail
Pour part “B” into the same pail with the part “A”
Mix thoroughly
Very important-Mix “B” into “A” in small quantities slowly. Product has an approximate ½ hour working time.

Application: Material can be applied by brush, roller, squeegee or low pressure spray equipment. Ensure product is applied in an even and uniform manner, making sure recesses and edges are thoroughly coated.

Handling and storage: The reaction of isocyanates Part A with water leads to the formation of insoluble ureas and carbon dioxide gas, which gas become contaminated with moisture should not be subsequently sealed; otherwise a hazardous increase in pressure may result.

ORBL-BM/C: Resistant to short-term exposure to low temperatures. However, low temperatures will result in increased viscosity, which makes handling more difficult. It is not advisable to store ORBL-BM for long periods below 32˚F (0˚C). The recommended storage temperature for Bedliner Batch Mix is 60˚-95²F. A small amount of insoluble solids in the A-side liquid product does not usually cause difficulties in handling or product performance. However, if necessay6r, the liquid product may be filtered through a suitable in-line filter.

Warranty

The technical data and any other printed information furnished by EFP LLC are true and accurate to the best of our knowledge. Aliphatic Polyurea conforms to in house quality control procedures and should be considered free of defects. The data provided is believed to be reliable and is offered solely for evaluation. The use of this product is beyond the control of the seller therefore the buyer assumes all risks of use and handling whether done in a matter that is in accordance with the provided posted directions or not. EFP LLC makes no warranty; expressed or implied, of its products and shall not be liable for indirect or consequential damage in any event